Search:

Type: Posts; User: shima

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    3,552

    Hello Steve, Thank you so much for your help. I...

    Hello Steve,
    Thank you so much for your help. I could get it to work.

    Regards,
    Shima
  2. Replies
    7
    Views
    3,552

    Hello Steve, I am trying to run tutorial 7 on...

    Hello Steve,
    I am trying to run tutorial 7 on the new FEBio, but I keep getting an error that reads "FATAL ERROR: unrecognized tag "control" (line 5)".
    Can you please help me with this?

    Thanks...
  3. Replies
    0
    Views
    403

    problem with contact between two interfaces

    I am modeling uterus, cervix and amniotic for my thesis, but a contact problem keeps emerging and after six months I still don't have results.

    I have a problem with contact between the uterus and...
  4. Replies
    7
    Views
    1,183

    sorry for the late reply, but I had to check...

    sorry for the late reply, but I had to check everything to see if they were ok and my FEBio couldn't run my model, it took me a while till I could update it and make it work, I do still have the...
  5. Replies
    7
    Views
    1,183

    I did as you said, I also updated my FEBio but...

    I did as you said, I also updated my FEBio but the problem still persists. It either gives an error termination or the amniotic sac passes through the uterus.
    what should I do?
  6. I keep getting the error that postview can't read my output file

    I keep getting this error when I try to open the output of my model.
    1655

    what should I do?
  7. Replies
    7
    Views
    1,183

    Hi I've just sent you the model. Thanks a lot...

    Hi
    I've just sent you the model. Thanks a lot for your time
  8. Replies
    7
    Views
    1,183

    thanks for your prompt reply, I've put penalty...

    thanks for your prompt reply, I've put penalty value on 100 and also enabled augmentation, now I get negative Jacobins and amniotic sac still penetrates the uterus. My material and boundary...
  9. Replies
    7
    Views
    1,183

    How can I enforce a sticky contact in FEBio?

    I am currently modeling uterus cervix and amniotic sac in FEBio and I have this problem with enforcing sticky contact. I'm applying force as the pressure inside the amniotic sac, there's a sticky...
  10. Replies
    2
    Views
    628

    I still have some problems with my model can...

    I still have some problems with my model can anyone help me out? please?
  11. I've read preview manual but I couldn't get how I...

    I've read preview manual but I couldn't get how I could set fiber orientation when I don't want it to be spherical or parallel to a vector because my model is rather complex and these two won't give...
  12. Is there an step to step guide for fiber generation

    Hi,
    My project is about biomechanical forces on uterus and cervix during pregnancy, and I need to use continuous fiber distribution material, I choose it from material but I don't know how should I...
  13. Replies
    2
    Views
    628

    I've made some changes in the model now I can run...

    I've made some changes in the model now I can run it, but it won't go past 0%
  14. Replies
    2
    Views
    628

    can't run my model

    Hi Steve
    I recently have started my University project with FEBio, it's about mechanical aspect of pregnancy. In most of my reference articles, they used FEBio.
    I created my model with Preview, and...
  15. Replies
    2
    Views
    949

    Thanks a lot sir

    Thanks a lot sir
  16. Replies
    2
    Views
    949

    does FEBio support FSI?

    hi
    I'm currently working on a master project on the biomechanics of pregnant uterus and I'm looking forward to using FEBio for the simulation part. But since my supervisor is insisting on modeling...
Results 1 to 16 of 16